PCFprog

[amgadtoony]

Mr Girts , Mr Solitaire
i make the connection according to MK3 pdf file connectios and used the dumps as i sent to you , so i need a video that describes the steps exactly
with my best regards

[solitaire]

Why you ask here? Why you not ask file seller?

[amgadtoony]

i ask here because i bought my pcfprog programmer from here , and i don't mind to buy the software from you if mine is wrong

[efka]

Where did you get your files from? That is the question

[amgadtoony]

thanks for all i solved the problem i must choose the right eeprom size from setting
don
thanks

[Girts]

User manual for beginners:

There are some basic rules to avoid key damage.
Keep in mind that "CONFIG" function is intended for advanced users.

• Install drivers (tested on WIN XP and WIN 7 32BIT)
• Before working make these settings - set EPROM to 8192 and EEPROM to 1024, then set BOOT MCU in KEY 7945;7952;7953
  Before utilising Erase function make sure you selected proper EPROM and EEPROM selection according to MCU type in the key
• Some keys use only EEPROM. In that case there will be no EPROM folder avaliable.
• Make sure you use proper dump files for the key.

Step by step guide

• disassemble key , remove battery
• Start software, select "SETTINGS" , choose proper EEPROM size (you can check it in key file folder) , then set correct EPROM size. After that select proper KEY MCU type (45/52/53 or 41/61)
• Execute "ERASE" function. Sofware will respond with DONE in bottom right corner
• Select FILE LOAD, choose correct EEPROM dump, push WRITE button. Software will respond with OK
• Select FILE LOAD, choose correct EPROM dump, push write function. Software will respond with OK.
• Open "CHIP" and utilise "Protect" function. If procedure executed correctly software will respond with "DONE" in the bottom right corner

Thats IT.
Your Key is ready.

[marcin2502]

When connecting pcfprog to laptop it does not detect device, in pcf programmer - "no device". I tried to connect to windows xp and windows 10 has some idea to work

[Girts]

Download and install drivers from FTDI site.
http://www.ftdichip.com/FTDrivers.htm

[marcin2502]

Unfortunately the remote device unrecognized. When connected to the notbook ,1 times the orange LED flashes and then no reaction. On windows 10 device information not recognized, windows xp does not detect the device



The drivers on this page work because I am working on an ecu tool that goes to these drivers

[marcin2502]

after installing on new clean system windows 7 attempt to run pcf programmer ends with error "can not run program not found FTD2XX.dll"

[Daniulis]

So, did you try to copy file "FTD2XX.dll" in to the parent folder of the software?

[marcin2502]

Continue unchanged. Pcfprogrammer starts but does not detect the device. The manager of the device did not appear. Once connected, the device blinks once and blinks. Installed D2XX driver from the link above, I already have ideas come to an end. I currently have a clean windows 7 basic system

[Girts]

Another PC?
Another cable?
Printscreen from "device manager"?

[marcin2502]

Hi, so the case was explained. I installed windows xp with sp3. After connecting the PCFprog the device was installed and working immediately

[efka]

On your other systems you are missing some frameworks Keep in mind if you have latest frame network it does not mean anything you must have earlier ones too....

[rgs]

hello
I have a question after virginise 285974100R_433 remote don t work
thanks for help

[Arriazu]

Consult, with which equipment can the ID be changed in the PCF79xx?

Thanks

[AutoKeyEcu]

to change the ID in PCF, you need to make binary arimetica,
To be able to do experiments, it is advisable to do this ¡¡¡ viewtopic.php?f=30&t=1807

[antuk]

Hello, френды

Хелп ми плиз PCF7953 36 pin connect pinout .

Можно распиновочку подключки ?

Ну если ещё на форд - ваще зацылую

[Girts]

Седьмой пост на первой странице этой темы - некатит?